soldering and rework system cartridge heater technology provides soldering and rework performance to suit even the most demanding smt removal and placement applications. the cartridges provide fast thermal performance and respond quickly to the load demands. a small shaft diameter provides access to tightly cramped rework areas and enables the most difficult operations to be performed effortlessly. mfr-src soldering & rework system part no. description mfr-src soldering and rework system includes mfr-ps1k two port universal voltage power supply mfr-hsr soldering and rework hand-piece mfr-wssr soldering workstand contents subject to change without notice standard soldering tip cartridges the standard soldering tip cartridges are used with the mfr-hsr soldering & rework hand-piece and have been designed to deliver outstanding performance for the majority of point-to-point mfr-ptz, mfr-src, mfr-pst, mfr-stz ambient operating temperature:10- 40c maximum enclosure temperature:55c input line voltage:100- 240 vac, grounded circuit input line frequency:50/60 hz power consumption:65 watts max. output power: 50 watts max. at 22c ambient temperature output frequency:450 khz power cord 3-wire:183cm (18/3") sjt power supply dimensions w x d x h: 122mm x 200mm x 152.5mm (4.8" x 8" x 6") agency tested per:iec 61000-6-1,ec 61000-6-3 and ul499, fcc cfr part 15 tip-to-ground potential:< 2mv tip-to-ground resistance:< 2 ohms idle temperature stability: 1.1c in still air hand-piece cable length: l=71cm (48"), burn proof, esd safe connector:8-pin power connector workstand dimensions w x d x h: 100 mm x 200 mm x 100 mm (4" x 8" x 4")
soldering and basic rework applications. the geometries within the range have been optimized to deliver maximum accessibility combined with optimal thermal efficiency within a narrow cartridge diameter. sfp-bvl10 bevel cartridge, 60 1.0mm (.04") sfp-ch10 chisel cartridge, 30 1.0mm (.04") sfp-ch15 chisel cartridge, 30 1.5mm (.06") sfp-ch20 chisel cartridge, 30 2.0mm (.08") sfp-ch25 chisel cartridge, 30 2.5mm (.10") SFP-CH50 chisel cartridge, 30 5.0mm (.20") sfp-chb15 chisel cartridge, 30 bent 1.5mm (.06") sfp-chl20 chisel cartridge, 60 long reach 2.0mm (.08") sfp-cn04 conical cartridge, 0.4mm (.016") with hand soldering, the task is to make a quality solder connection, without damaging the substrate and without negatively impacting throughput. all of the standard mfr series power tips & rework cartridges are designed for use with glass fiber (fr4) pcb substrates. this is denoted by the second letter in the part number: "f". for example: sfp-ch10, dfp-cn3, and sfv-cnl10. however, some specialist applications require working with thermally demanding or temperature sensitive substrates, such as ceramic hybrids or flexible circuits. ok international has developed specialty heaters that quickly deliver the necessary power, but operate at temperatures that minimize the risk of substrate damage. these are denoted by replacing the "f" in the part number with a "t" for temperature sensitive or a "c" for demanding loads. please contact your local representative for information and availability of specialty tip heaters. for example: stp-ch10 and dcp-cn3. f = standard fr4 substrate t = temperature sensitive c = ceramic or heavy load
sfp-cn05 conical cartridge, 0.5mm (.02") sfp-cnb04 conical cartridge bent, 0.4mm (.016") sfp-cnb05 conical cartridge bent, 0.5mm (.02") sfp-cnl04 conical cartridge long reach, 0.4mm (.016") sfp-drh05 drag soldering cartridge, hoof 0.5mm (.02") sfp-drh15 drag soldering cartridge, hoof 1.5mm (.06") sfp-drh35 drag soldering cartridge, hoof 3.5mm (.14") sfp-drk50 drag soldering cartridge, knife 5.0mm (.20") to order specialty versions of the soldering tip cartridges replace the "f" in the part number with the appropriate letter designate for your application when ordering: t = temperature sensitive c = ceramic or heavy load rework cartridges the rework cartridges are used with the mfr-hsr soldering & rework hand-piece for conduction rework of surface mount components. the geometries are compatible with common smt chip and soic components. mfr-smt in action
blade cartridges part no. description a rfp-bl1 blade cartridge 10mm (0.4") rfp-bl2 blade cartridge 16mm (0.63") rfp-bl3 blade cartridge 22mm (0.87") slot cartridges part no. smt type a rfp-sl1 0805 chip package 2.34mm (.092")
rfp-sl2 1206 chip package 3.48mm (.137") tunnel cartridges dimensions in mm (") part no. smt type a2 a b d rfp- dl1 soic 14-16 5.18 (.204) 5.18 (.204) 4.32 (.17) 3.22 (.127) rfp- dl2 soic 8 5.18 (.204) 5.18 (.204) 4.32 (.17) 2.29 (.090) rfp- dl13 soic 16 6.86 (.270) 6.86 (.270) 11.18 (.44) 2.29 (.090) quad cartridges dimensions in mm (") part no. smt type a2 a b2 b d rfp- qd4 plcc 32 11.43 (.450) 12.70 (.500) 13.97 (.550) 15.24 (.600) 3.81 (.150)
rfp- qd6 plcc 44 16.76 (.660) 17.78 (.700) 16.76 (.660) 17.78 (.700) 3.81 (.150) rfp- qd7 plcc 68 24.38 (.960) 25.27 (.995) 24.38 (.960) 25.27 (.995) 5.59 (.220) rfp- qd10 plcc 52 19.30 (.760) 20.32 (.800) 19.30 (.760) 20.32 (.800) 3.81 (.150) rfp- qd15 tqfp 80 12.32 (.485) 13.34 (.535) 12.32 (.485) 13.34 (.535) 2.79 (.110) rfp- qd19 qfp 44 16.13 (.635) 16.13 (.635) 16.13 (.635) 16.13 (.635) 3.30 (.130) rfp- qd20 qfp 100 16.51 (.650) 16.51 (.650) 22.48 (.885) 22.48 (.885) 3.30 (.130) the second digit denotes substrate material (damage tolerance). f = fr4 / glass fiber, for most standard applications. two other series are also available; just replace f with either t or c. t = temperature sensitive c = ceramic or heavy load ? 2007 ok international. all rights reserved. http://www.okinternational.com/product_soldering_mfr/mfr_src (6 of 6) [3/28/08 1:37:12 pm]
|
